[2018-4-NEW] Most Accurate Cisco 100-105 Dumps ICND1 Exam Video Actual Test Covers All Key Points (Question 1 – Question 13)

Preparing your 100-105 dumps? 100-105, Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) is a proctored exam offered by pass4itsure Cisco. This exam is specially linked with (ICND1) Cisco certified solutions Expert. This exam is available in English, Japanese. Candidates connected with IT field can apply for pass4itsure 100-105 dumps pdf Cisco certification exams, and this is a CCENT, CCNA Routing & Switching, CCDA, CCNA Security, CCNA Wireless certification technology. The exam is closed book and no outside reference materials are allowed.

Interconnecting Cisco Networking Devices Part 1
Exam Number: 100-105 ICND1
Associated Certifications: CCENT, CCNA Routing & Switching, CCDA, CCNA Security, CCNA Wireless
Duration: 90 Minutes (45-55 questions)
Available Languages: English, Japanese

Up to the immediate present 100-105 exam cram(1-13)

Question No : 1 – (Topic 1)
Refer to the exhibit.
100-105 dumps
Mary is sending an instant message to Robert. The message will be broken into a series of packets that will traverse all network devices. What addresses will populate these packets as they are forwarded from Router1 to Router2?
100-105 dumps
A. Option A
B. Option B
C. Option C
D. Option D
E. Option E
100-105 exam Answer: B
Explanation:
The Source and Destination IP address is not going to change. Host 1 IP address will stay as being the source IP and the Host 2 IP address will stay the destination IP address. Those two are not going to change. For the MAC address it is going to change each time it goes from one hope to another. (Except switches… they don’t change anything) Frame leaving HOST 1 is going to have a source MAC of Host 1 and a destination MAC of Router 1. Router 1 is going to strip that info off and then will make the source MAC address of Router1’s exiting interface, and making Router2’s interface as the destination MAC address.
Then the same will happen… Router2 is going to change the source/destination info to the

Question No : 2 – (Topic 1)
A workstation has just resolved a browser URL to the IP address of a server. What protocol will the workstation now use to determine the destination MAC address to be placed into frames directed toward the server?
A. HTTP
B. DNS
C. DHCP
D. RARP
E. ARP
100-105 dumps Answer: E
Explanation:
The RARP protocol is used to translate hardware interface addresses to protocol addresses. The RARP message format is very similar to the ARP format. When the booting computer sends the broadcast ARP request, it places its own hardware address in both the sending and receiving fields in the encapsulated ARP data packet. The RARP server will fill in the correct sending and receiving IP addresses in its response to the message. This way the booting computer will know its IP address when it gets the message from the RARP server

Question No : 3 – (Topic 1)
Which protocol uses a connection-oriented service to deliver files between end systems?
A. TFTP
B. DNS
C. FTP
D. SNMP
E. RIP
Answer: C
Explanation:
TCP is an example of a connection-oriented protocol. It requires a logical connection to be established between the two processes before data is exchanged. The connection must be maintained during the entire time that communication is taking place, then released afterwards. The process is much like a telephone call, where a virtual circuit is established-
-the caller must know the person’s telephone number and the phone must be answered– before the message can be delivered.
TCP/IP is also a connection-oriented transport with orderly release. With orderly release, any data remaining in the buffer is sent before the connection is terminated. The release is accomplished in a three-way handshake between client and server processes. The connection-oriented protocols in the OSI protocol suite, on the other hand, do not support orderly release. Applications perform any handshake necessary for ensuring orderly release. Examples of services that use connection-oriented transport services are telnet, rlogin, and ftp.

Question No : 4 – (Topic 1)Refer to the exhibit.
100-105 dumps
If the hubs in the graphic were replaced by switches, what would be virtually eliminated?
A. broadcast domains
B. repeater domains
C. Ethernet collisions
D. signal amplification
E. Ethernet broadcasts
Answer: C
Explanation:
Modern wired networks use a network switch to eliminate collisions. By connecting each device directly to a port on the switch, either each port on a switch becomes its own collision domain (in the case of half duplex links) or the possibility of collisions is eliminated entirely in the case of full duplex links.

Question No : 5 – (Topic 1)
Refer to the exhibit.
100-105 dumps
Host A is sending a packet to Host B for the first time. What destination MAC address will Host A use in the ARP request?
A. 192.168.0.1
B. 172.16.0.50
C. 00-17-94-61-18-b0
D. 00-19-d3-2d-c3-b2
E. ff-ff-ff-ff-ff-ff
F. 255.255.255.255
100-105 pdf Answer: E
Explanation:
For the initial communication, Host A will send a broadcast ARP (all F’s) to determine the correct address to use to reach the destination. ARP sends an Ethernet frame called an ARP request to every host on the shared link-layer legmen. The Ethernet header includes the source host MAC address and a destination address of all Fs representing a broadcast frame. The ARP request contains the sender’s MAC and IP address and the target (destination) IP address. The target’s MAC address is
set to all 0s. ARP Request
Reference:

Question No : 6 – (Topic 1)
Refer to the exhibit.
100-105 dumps
What kind of cable should be used to make each connection that is identified by the numbers shown?
A. 1 – Ethernet Crossover cable
2 – Ethernet straight-through cable
3 – Fiber Optic cable
4 – Rollover cable
B. 1 – Ethernet straight-through cable
2 – Ethernet straight-through cable
3 – Serial cable
4 – Rollover cable
C. 1 – Ethernet rollover cable
2 – Ethernet crossover cable
3 – Serial cable
4 – Null-modem cable
D. 1 – Ethernet straight-through cable
2 – Ethernet Crossover cable
3 – Serial cable
4 – Rollover cable
E. 1 – Ethernet straight-through cable
2 – Ethernet Crossover cable
3 – Serial cable
4 – Ethernet Straight-through cable
Answer: B
Explanation:
When connecting a PC to a switch, a standard Ethernet straight through cable should be used. This same cable should also be used for switch to router connections. Generally speaking, crossover cables are only needed when connecting two like devices (PC-PC, switch-switch, router-router, etc). Routers connect to frame relay and other WAN networks using serial cables. Rollover cables are special cables used for connecting to the console ports of Cisco devices.

Question No : 7 – (Topic 1)Refer to the exhibit.
100-105 dumps
SwitchA receives the frame with the addressing shown. According to the command output also shown in the exhibit, how will SwitchA handle this frame?
A. It will drop the frame.
B. It will forward the frame out port Fa0/6 only.
C. It will flood the frame out all ports.
D. It will flood the frame out all ports except Fa0/3.
100-105 pdf Answer: B
Explanation:
Switches keep the learned MAC addresses in a table, so that when a frame comes in with a destination MAC address that the switch has already learned, it will forward it to that port only. If a frame comes in with a destination MAC that is not already in the MAC address table, then the frame will be flooded to all ports except for the one that it came in on. In this case, Switch A already knows that 00b0.d0da.cb56 resides on port fa0/6, so it will forward the from out that port.

Question No : 8 – (Topic 1)
Which statements accurately describe CDP? (Choose three.)
A. CDP is an IEEE standard protocol.
B. CDP is a Cisco proprietary protocol.
C. CDP is a datalink layer protocol.
D. CDP is a network layer protocol.
E. CDP can discover directly connected neighboring Cisco devices.
F. CDP can discover Cisco devices that are not directly connected.
Answer: B,C,E
Explanation:
CDP (Cisco Discovery Protocol) is a proprietary protocol designed by Cisco to help administrators collect information about both locally attached and remote devices. By using CDP, you can gather hardware and protocol information about neighbor devices containing useful info for troubleshooting and documenting the network.

Question No : 9 – (Topic 1)
Refer to the exhibit.
100-105 dumps
A network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation?
A. a router with two Ethernet interfaces
B. a switch with two Ethernet interfaces
C. a router with one Ethernet and one serial interface
D. a switch with one Ethernet and one serial interface
E. a router with one Ethernet and one modem interface
Answer: C
Explanation:
Only a router can terminate a leased line attachment access circuit, and only a router can connect two different IP networks. Here, we will need a router with two interfaces, one serial connection for the line attachment and one Ethernet interface to connect to the switch on the LAN.

Question No : 10 – (Topic 1)
What must occur before a workstation can exchange HTTP packets with a web server?
A. A UDP connection must be established between the workstation and its default gateway.
B. A UDP connection must be established between the workstation and the web server.
C. A TCP connection must be established between the workstation and its default gateway.
D. A TCP connection must be established between the workstation and the web server.
E. An ICMP connection must be established between the workstation and its default gateway.
F. An ICMP connection must be established between the workstation and the web server.
100-105 vce Answer: D
Explanation:
HTTP uses TCP port 80, and a TCP port 80 connection must be established for HTTP communication to occur.

Question No : 11 – (Topic 1)
Refer to the exhibit.
100-105 dumps
HostX is transferring a file to the FTP server. Point A represents the frame as it goes toward the Toronto router. What will the Layer 2 destination address be at this point?
A. abcd.1123.0045
B. 192.168.7.17
C. aabb.5555.2222
D. 192.168.1.1
E. abcd.2246.0035
Answer: E
Explanation:
For packets destined to a host on another IP network, the destination MAC address will be the LAN interface of the router. Since the FTP server lies on a different network, the host will know to send the frame to its default gateway, which is Toronto.

Question No : 12 – (Topic 1)
Refer to the exhibit.
100-105 dumps
A network has been planned as shown. Which three statements accurately describe the areas and devices in the network plan? (Choose three.)
A. Network Device A is a switch.
B. Network Device B is a switch.
C. Network Device A is a hub.
D. Network Device B is a hub.
E. Area 1 contains a Layer 2 device.
F. Area 2 contains a Layer 2 device.
100-105 exam Answer: A,D,E
Explanation:
Switches use a separate collision domain for each port, so device A must be a switch. Hubs, however, place all ports in the same collision domain so device B is a hub. Switches reside in layer 2 while hubs are layer 1 devices.

Question No : 13 – (Topic 1)
Which layer of the TCP/IP stack combines the OSI model physical and data link layers?
A. Internet layer
B. transport layer
C. application layer
D. network access layer
Answer: D
Explanation:
The Internet Protocol Suite, TCP/IP, is a suite of protocols used for communication over the internet. The TCP/ IP model was created after the OSI 7 layer model for two major reasons. First, the foundation of the Internet was built using the TCP/IP suite and through the spread of the World Wide Web and Internet, TCP/IP has been preferred. Second, a project researched by the Department of Defense (DOD) consisted of creating the TCP/IP protocols. The DOD’s goal was to bring international standards which could not be met by the OSI model. Since the DOD was the largest software consumer and they preferred the TCP/IP suite, most vendors used this model rather than the OSI. Below is a side by side comparison of the TCP/IP and OSI models.

100-105, Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) exam is consists of different types of multiple choice questions and answers. In the pass4itsure 100-105 dumps exam resources, It will be the hot test associated with Cisco 100-105 practice exam qualification and you will cover every field and category in Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) helping to ready you for your successful CCENT, CCNA Routing & Switching, CCDA, CCNA Security, CCNA Wireless Certification.

[2018-4-NEW Pass4itsure 100-105 PDF Dumps Questions From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWeVQ5WUxjZG1Idnc

[2018-4-NEW Pass4itsure 200-105 PDF Dumps Questions From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWWWw0QXQxY3R1X1E

In most cases pass4itsure 100-105 exam collection may include 80% or so of the real test questions. If you master all questions and answers you will get 80% at least. So spending a small amount of time and money in exchange for such a good result is worthful. Please add pass4itsure 100-105 dumps pdf training tool in your shopping cart now. Pass4itsure’s experienced expert team has developed effective training program a for cisco certification 100-105 dumps, which is very fit for candidates.

pass4itsure 100-105 dumps

I will highly recommend you to try pass4itsure.com for your 100-105 dumps for exam preparation. More important is that pass4itsure 100-105 dumps exam answers are applicable to all the IT exam. They provides you 100% valid and accurate 100-105 dumps with money back guarantee in case of failure.

100-105 dumps
Pass4itsure Cisco 100-105 Dumps Test Prep, Most Accurate Pass4itsure Cisco 100-105 Dumps Actual Test Covers All Key Points, We Help You Pass Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0). Pass4itsure 100-105 Dumps Exam Youtube Free Online Test Here:

[2017-9-NEW] High Pass Rate Cisco CCENT 100-105 Dumps PDF ICND1 v3.0 Study Plan with Real Exam Questions And Answers [Video]

Are You really ready to take Cisco ICND1 100-105 dumps? “Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)” is the 100-105 exam dumps which covers all the knowledge points of the real Cisco exam. High Pass Rate Cisco CCENT 100-105 dumps pdf ICND1 v3.0 study plan with real exam questions and answers. Pass4itsure 100-105 dumps exam questions answers are updated (332 Q&As) are verified by experts.  At present, Cisco https://www.pass4itsure.com/100-105.html dumps exam answers really enjoys tremendous popularity.

Exam Code: 100-105
Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)
Updated: Sep 03, 2017
Q&As: 332

[2017-9-NEW Cisco 100-105 Dumps From Google Drive]:https://drive.google.com/open?id=0BwxjZr-ZDwwWeVQ5WUxjZG1Idnc

[2017-9-NEW Cisco 210-255 Dumps From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWOXlNazlKRi1GcFU

100-105 dumps

QUESTION NO: 34
Productivity is increased if value is added to a product.
A. True
B. False
100-105 exam 
Answer: A
QUESTION NO: 35
Quality assurance is the process by which product quality is compared with applicable standards,
and the action taken when nonconformance is detected.
A. True
B. False
Answer: A
QUESTION NO: 36
A latent defect is the same as a fault.
A. True
B. False
100-105 dumps 
Answer: A
QUESTION NO: 37
Quality and quality assurance are synonymous.
A. True
B. False
Answer: B
QUESTION NO: 38
Vision is a clear definition of the result you are trying to achieve.
A. True
B. False
100-105 pdf 
Answer: A
QUESTION NO: 39
A standard is not an expected norm
A. True
B. False
Answer: B
QUESTION NO: 40
Quality control relates to a specific product or service.
A. True
B. False
100-105 vce 
Answer: A
QUESTION NO: 41
Which two elements are the major causes of documentation problems? (Choose any Two)
A. Forgetfulness
B. Not enough time
C. Personal attitudes
D. Low priority
Answer: C,D
QUESTION NO: 42
Almost one-half of a programmer’s time is spent identifying and fixing errors in specifications.
A. True
B. False
100-105 exam 
Answer: A
QUESTION NO: 43
What is the present value of money of a $10,000 expenditure that you will spend one year from
now if money is worth 14 percent?
A. $1600
B. $8770
C. $8600
D. $2630
Answer: B
QUESTION NO: 44
National Quality Awards are intended to foster continuous improvement activities.
A. True
B. False
100-105 dumps 
Answer: A
QUESTION NO: 45
The objective of the present value of money calculation is to convert future dollars into current
dollars.
A. True
B. False
Answer: A
QUESTION NO: 46
In the IT workbench, quality, and performance of the work are the responsibility of the QA
department.
A. True
B. False
100-105 pdf 
Answer: B
QUESTION NO: 47
The process used for documenting user’s requirements is known as validation.
A. True
B. False
Answer: B
QUESTION NO: 48
A large portion of the cost of quality is usually the cost of rework.
A. True
B. False
100-105 vce 
Answer: A
QUESTION NO: 49
Function points quantify data processing work outputs.
A. True
B. False
Answer: A
QUESTION NO: 50
Function points are hardware and software independent.
A. True
B. False
100-105 exam 
Answer: A
QUESTION NO: 51
The inspection is an evaluation technique that relies on visual examination of an item.
A. True
B. False
Answer: A
QUESTION NO: 52
The three parts of the function point count must be determined individually.
A. True
B. False
100-105 dumps 
Answer: A
QUESTION NO: 53
The intent of the quality control checklist should be to improve the quality of the product being
controlled by investigative means.
A. True
B. False
Answer: A
QUESTION NO: 54
Measurement of function points cannot be used for comparing two different kinds of systems.
A. True
B. False
100-105 pdf 
Answer: B
QUESTION NO: 55
A process/activity during which a high number of defects occur is known as a defect-prone
process.
A. True
B. False
Answer: A
QUESTION NO: 56
The number-one skill needed for the tester analyst is listening.
A. True
B. False
100-105 vce 
Answer: A
QUESTION NO: 57
A program whose purpose is to reduce the number of defects produced is known as a quality
improvement program.
A. True
B. False
Answer: A
QUESTION NO:58 You want to implement site level disaster recovery. Which two are valid options to consider? (Choose two.)
A. Use SAN Copy to copy LUNs from the primary site to the recovery site.
B. Use SAN Copy to mirror a LUN from the primary site to the recovery site. C.
Use MirrorView to mirror LUNs from the primary site to another local array.
D. Use SnapView to create a clone, then use SAN Copy to copy the clone to the recovery site.
100-105 exam Answer: AD
QUESTION NO:59 You have installed SAN Copy. Which 100-105 dumps statement is true?
A. The storage array must be rebooted.
B. SAN Copy cannot be upgraded, except by a complete re-install.
C. Any LUN within the SAN is automatically made available to be copied.
D. The admhost utility must be installed on each storage array that Navisphere Manager resides on.
E. SAN Copy sessions can be managed through the Navisphere Manager Enterprise Storage window.
Answer: E
QUESTION NO:60 Which three statements are correct about using SnapView? (Choose three.)
A. Snapshots can take mere seconds to create.
B. Snapshots may be created using the admhost CLI utility.
C. SnapView can take snapshots, or point-in-time copies of LUNs. D.
SnapView can make clones, or 100% duplicate copies of a LUN. E.
Snapshots are volume-level and thus able to restore specific files.
Answer: ACD
QUESTION NO:61 Which three statements are correct about clones? (Choose three.)
A. Clones can be copied using SAN Copy to a remote storage array.
B. Clones typically consume about 20% of the size of the source LUN.

C. Fractured clones can later be synchronized with the source LUN to update the contents.
D. Clones can be fractured from the source LUN, then mounted to a secondary host and accessed just
like another LUN.
100-105 pdf Answer: ACD
QUESTION NO:62 You want User1 to have Administrator access to storage system A that is located in a branch office.
However, you want User1 to have read-only access to the remaining storage systems within the domain.
Which scenario best accomplishes this task?
A. User accounts must be either global or local because the user inherits the most restrictive role
assigned to the user.
B. Create a local account with Administrator access on storage system A, then create a global account for
User1 with Monitor access.
C. Create a global account with Monitor access on storage system A, then modify the account policy to
allow User1 to administer only storage system A.
D. Create a global account with Monitor access on the master node, then have User1 log in to storage
system A using the local default manager account.
Answer: B

As far as you that you have not got the certificate, do you also want to take 100-105 exam answers? Cisco 100-105 dumps exam answers is really hard examination. But it doesn’t mean that you cannot get high marks and pass the exam easily. Do you want to know the Pass4itsyre skills? Now, I would like to tell you making use of Pass4itsure https://www.pass4itsure.com/100-105.html dumps exam answers and answers can help you get the certificate.